How to Size a Demister for a Given Gas Flow Rate
11/09/2026Demister Flooding and Re-entrainment: Causes, Diagnosis and Fixes
11/09/2026Expect 0.1–0.3 kPa dry and 0.2–0.6 kPa wet from a knitted wire mesh demister, 0.1–0.5 kPa from a vane pack, and 0.5–2 kPa from a fiberbed candle filter. Any mesh pad reading above about 1 kPa is operating outside its design envelope, and the cause is almost always velocity, liquid loading or a blocked drainage path rather than a defect in the element itself.
Pressure drop is the parameter plant operators actually see, because it is the number on the differential pressure transmitter. Learning to read it is the fastest way to diagnose a mist eliminator that is starting to fail — usually weeks before carryover becomes visible downstream.
Typical values by internal type
| Internal type | Dry ΔP | Wet ΔP | Alarm threshold | Main driver |
|---|---|---|---|---|
| Knitted wire mesh, 100 mm, 120 kg/m³ | 0.10–0.20 kPa | 0.20–0.40 kPa | > 0.6 kPa | Velocity, drainage |
| Knitted wire mesh, 150 mm, 180 kg/m³ | 0.15–0.30 kPa | 0.30–0.60 kPa | > 0.8 kPa | Velocity, fouling |
| Vane pack / chevron | 0.10–0.30 kPa | 0.20–0.50 kPa | > 0.8 kPa | Blade angle, liquid load |
| Corrugated plate media | 0.05–0.20 kPa | 0.10–0.30 kPa | > 0.5 kPa | Plate spacing |
| Fiberbed candle filter, standard grade | 0.50–1.20 kPa | 0.80–1.80 kPa | > 2.0 kPa | Media grade, bed depth |
| Fiberbed candle filter, fine grade | 1.00–2.00 kPa | 1.50–3.00 kPa | > 3.5 kPa | Media grade, solids loading |
These ranges assume a clean element, correctly sized, with a working drainage path. If your measured value sits outside the range at commissioning, the element or the installation is wrong. If it sits inside the range at commissioning and climbs over months, the process is fouling the element or the flow has increased.
How velocity drives pressure drop
Dry pressure drop through a porous bed scales roughly with the square of the approach velocity:
ΔPdry ∝ u²
The practical consequence is blunt. Raise the flow 30% and the dry pressure drop rises about 70%. Raise it 50% and it rises 125%. A debottleneck that pushes 40% more gas through an existing demister does not just reduce efficiency — it can push the pad into flooding and take the whole pressure drop with it.
With liquid present the exponent is worse than two, because the liquid film reduces the open area and the gas has to accelerate through the remaining passages. This is why wet pressure drop is not simply dry pressure drop plus a constant.
What a rising trend actually tells you
| Pattern | Most likely cause | Check |
|---|---|---|
| Slow, steady rise over weeks or months | Solids or polymer fouling of the mesh | Inspect a sample of the pad, check upstream for solids carryover, review wash or irrigation frequency |
| Step change coinciding with a flow increase | Operation above design velocity | Recalculate Souders-Brown at current conditions and compare with design |
| Sudden rise plus carryover | Flooding, blocked drain or collapsed element | Check drain path, liquid level, and inspect the pad for deformation |
| Oscillating pressure drop | Liquid slugs or unstable two-phase inlet | Review inlet device performance and upstream slug catchers |
| High from day one | Wrong mesh density, over-thick bed, blocked support | Verify against the datasheet and confirm the support grid is open |
The pressure drop you should budget at design stage
For new projects, budget these values in the system pressure balance so you are not surprised later:
- Wire mesh demister: 300 mm water column (about 0.3 kPa) is a safe allowance; sizing at that value usually leaves the element running well below it
- Vane pack: 250–500 mm water column
- Fiberbed: 1000–2000 mm water column, and confirm the upstream fan or compressor has that margin available
On fiberbed installations the pressure drop allowance matters most, because a fine grade element in a saturated gas can cost 2–3 kPa continuously. Retrofits that replace a mesh pad with a fiberbed to meet a tighter emission limit frequently fail at the fan duty check, not at the separation duty.
Where to measure it
Measure across the element itself, not across the vessel. Taps should sit immediately upstream and downstream of the pad, in a region where the velocity profile is representative. A tap placed in the inlet nozzle wake reads the inlet momentum, not the pad resistance, and will mislead you for the life of the plant.
Also record the reading against flow, not against time alone. A pressure drop number without the corresponding flow is not diagnostic. See our wire mesh demisters, vane packs and fiberbed elements for typical performance data.
Frequently Asked Questions
What is a normal pressure drop across a demister?
A clean knitted wire mesh demister typically runs 0.1 to 0.3 kPa dry and 0.2 to 0.6 kPa when irrigated. Vane packs run 0.1 to 0.5 kPa. Fiberbed candle filters run 0.5 to 2 kPa, and fine grades in critical service can reach 3 kPa. Anything above roughly 1 kPa on a mesh pad is a warning sign, not a normal operating point.
Why does pressure drop increase over time?
Three mechanisms dominate: solids or polymer fouling blocking the open area, liquid holdup increasing as the pad wets and drainage degrades, and mechanical damage or collapse of the pad which reduces the free volume. A gradual rise is usually fouling; a sudden rise is usually flooding, a blocked drain or a collapsed element.
How does gas velocity affect demister pressure drop?
Dry pressure drop scales approximately with the square of the face velocity, so a 40 percent increase in flow nearly doubles the dry pressure drop. Once liquid loading becomes significant the relationship is steeper still, which is why operating above the design velocity causes pressure drop to climb far faster than the flow increase alone would suggest.
Which mist eliminator has the lowest pressure drop?
Vane packs and corrugated plate media have the lowest resistance per unit of flow, typically 0.1 to 0.5 kPa, because the gas path is open and relatively short. Knitted wire mesh sits in the middle. Fiberbed candle filters have the highest pressure drop because the gas is forced through a dense microfibre bed to capture sub-micron aerosol.
Worked example: scaling a measured pressure drop to a new duty
The most reliable way to predict pressure drop is to scale a reading you already have. For a fixed geometry, pressure drop follows density and velocity squared, so a measurement at one flow gives the value at another without any correlation.
| Step | Calculation | Result |
|---|---|---|
| Existing reading | Mesh pad, 1.0 m diameter, 150 mm bed, 8,000 kg/h air at 60 °C and 1 atm | 0.18 kPa |
| Volumetric flow, existing | 8,000 / 1.06 / 3600 | 2.10 m³/s |
| Face velocity, existing | 2.10 / 0.785 | 2.67 m/s |
| New duty | 10,000 kg/h, same conditions, pad 1.2 m diameter | 2.62 m³/s |
| Face area, new | π × 1.2² / 4 | 1.131 m² |
| Face velocity, new | 2.62 / 1.131 | 2.32 m/s |
| Velocity ratio squared | (2.32 / 2.67)² | 0.75 |
| Predicted pressure drop | 0.18 × 0.75 | 0.14 kPa |
The new pad runs at a lower velocity than the one measured, so the pressure drop falls even though the mass flow is higher. That is the point worth remembering: mass flow and velocity are not the same thing, and the diameter is what converts one into the other.
Fouling is not covered by this scaling. Pressure drop through a mesh pad rises roughly with the inverse square of the free area, so losing 30% of the open area to deposits multiplies the reading by about 2 — from 0.14 kPa to roughly 0.29 kPa at unchanged flow. That is the number to compare against the fan or blower budget when a pad has been in service for a year.
Worked example: the same duty in three technologies
| Internal | K (m/s) | u max (m/s) | Design at 70% | Face area for 2.62 m³/s | Diameter |
|---|---|---|---|---|---|
| Wire mesh, standard | 0.107 | 3.26 | 2.28 | 1.15 m² | 1.21 m |
| Vane pack | 0.152 to 0.183 | 4.63 to 5.58 | 3.24 to 3.90 | 0.81 to 0.67 m² | 1.02 to 0.93 m |
| Fiberbed element | face velocity 0.1 to 0.5 | — | 0.3 m/s typical | 8.7 m² | 3.3 m |
The vane pack fits in a vessel roughly 20% smaller in diameter, at the cost of a 20 to 30 micron cut point instead of 10. The fiberbed element needs several times the area because it is not sized on a capacity factor at all — it is sized on the face velocity the media can carry while still collecting sub-micron aerosol. That difference in physical size is why the technology decision belongs before the vessel decision, not after it.
- Gas-Liquid Separation Fundamentals — terminology, separation mechanisms and internal selection
- Technical Data Sheet — material and performance reference data
- All Technical Articles — complete engineering index
If you are working on a replacement
Most of the work behind an article like this is a replacement inside an existing vessel, where the available dimensions decide more than the nominal duty. See the process data needed to size and select it, the scope from data review through to delivery and what has to be supplied before a price is issued.
More on wire mesh demisters and demister pads
- How Does a Wire Mesh Demister Work? A Complete Guide – the guide that covers this device family end to end
- Demister Sizing: Why Western and Chinese Conventions Give Different Diameters
- Why the Same Demister Duty Gives Different Diameters: Five Conventions That Move the Answer
- Reboiler Mist Eliminators in Ethylene, C3 Splitter Heat Pumps and Refrigeration Chillers
- Why a Shorter Kettle Bundle Can Need a Larger Shell: Length, Diameter and Which Area Binds
Not sure which technology fits the duty at all? Which Mist Eliminator or Coalescer Do You Need? A Selection Map by Duty compares all four on droplet cut point, pressure drop and fouling tolerance.
