Vane Pack Design and Sizing: Channel Geometry, Drainage and Capacity

Cooling Tower Drift Eliminators: Drift Loss, Pressure Drop and Fouling Control
11/09/2026
Calming Baffles and Perforated Plates: Flow Distribution Design Rules
11/09/2026
Cooling Tower Drift Eliminators: Drift Loss, Pressure Drop and Fouling Control
11/09/2026
Calming Baffles and Perforated Plates: Flow Distribution Design Rules
11/09/2026

Short answer: a vane pack is a set of angled blades that force the gas to change direction repeatedly, so droplets hit the blade surface instead of following the gas. Its capacity comes from continuous drainage, not from a denser element. Design of the channel geometry, the number of passes and the drainage path decides whether it works; the material grade is secondary.

What the geometry controls

Four geometric parameters determine performance:

Parameter Typical range What it changes
Blade angle to flow about 30 to 45 degrees Sharper angle improves capture of fine droplets but increases pressure drop and improves drainage
Blade spacing (pitch) about 20 to 50 mm Narrower pitch improves efficiency and raises pressure drop; wider pitch resists fouling
Number of passes 2 to 4 Each extra pass raises efficiency and pressure drop; three passes is common for fine mist
Drainage arrangement pockets, notches, or a dedicated downcomer Decides whether separated liquid leaves the pack or is re-entrained

Vane packs are not a single product with one characteristic curve. Two units with the same outline dimensions and the same material can differ substantially in efficiency and pressure drop because the internal geometry differs. This is why a vane pack specification on a datasheet should state the number of passes and the pitch, not only the overall size.

Why drainage, not density, sets capacity

A knitted mesh pad stores liquid inside the mesh and depends on the liquid draining down through it. A vane pack, by contrast, drains each blade continuously: droplets collect on the blade face, run toward a notch or pocket, and leave the gas stream. Because the liquid residence time is short, a vane pack tolerates much higher liquid loads without flooding.

The failure mode at high load is therefore not flooding in the mesh sense but re-entrainment: liquid leaving the blade surface is sheared off by the gas before it reaches the drain. Signs are rising carryover at high liquid load with pressure drop still normal, and liquid visible on the downstream side of the pack.

Velocity and capacity

Vane packs commonly operate at 1.5 to 3 times the vapor velocity permitted by a wire mesh pad of comparable pressure drop. That capacity advantage is the reason vane packs are chosen for services with high liquid load, slugging risk or where the vessel diameter is fixed and the flow cannot be reduced.

The trade-off is efficiency: vane packs typically remove droplets down to about 20 to 30 microns, while a mesh pad reaches around 10 microns and a fiberbed element sub-micron. Where the outlet specification is tight, the correct combination is often a vane pack as a pre-separator followed by a mesh pad or fiberbed element as the polishing stage.

Pressure drop

A typical two to three pass vane pack sits around 0.1 to 0.5 kPa depending on pitch and velocity. Pressure drop rises roughly with the square of velocity, so an oversized flow through an undersized pack costs disproportionately in fan power. The pressure drop relationship is set out in What Pressure Drop Should You Expect from a Mist Eliminator?

Design checklist

  1. Fix the required outlet droplet size first; that decides whether a vane pack alone is sufficient.
  2. Determine liquid load in m3 per m2 of face area per hour, including turndown and upset cases.
  3. Select pitch and number of passes to meet efficiency within the pressure drop budget.
  4. Design the drainage path so liquid returns below the liquid level and away from the gas outlet.
  5. Check the pack fits the vessel, including access through the manway and support independent of the outlet nozzle.
  6. Confirm the material for the operating temperature and corrosion environment.

Installation points that decide the outcome

  • Support the pack on its own structure; do not hang it from the outlet nozzle or from the tray above.
  • Seal the pack to the vessel wall on all sides, otherwise gas bypasses at the edge.
  • Keep the drainage outlet clear of the liquid level to avoid back-flooding the pack.
  • Allow access for cleaning; fouling in narrow channels is harder to remove than in a mesh pad.

For the selection logic against other internal types see Fiberbed vs Wire Mesh Demister, and for inlet side momentum control see Vane Type Inlet Device.

Send gas flow, operating pressure and temperature, required outlet droplet size, liquid load and vessel dimensions and we will propose the pitch, pass count and pressure drop for your duty.

Frequently Asked Questions

What droplet size can a vane pack remove?

Typically down to about 20 to 30 microns in a well designed unit. Below that the efficiency falls quickly, and a wire mesh pad or a fiberbed element is the appropriate internal instead.

How much more gas velocity can a vane pack take than a wire mesh pad?

Commonly 1.5 to 3 times the vapor velocity allowed by a knitted mesh pad at the same pressure drop order, because the vane channels drain liquid continuously instead of storing it in the mesh.

Why does a vane pack re-entrain liquid at high load?

The drainage path is overwhelmed. Liquid leaves the vane surface faster than the pockets and downcomers can return it, so it is sheared off the blade and carried downstream. The fix is lower velocity or a design with positive drainage.

Should the vane pack be installed vertically or horizontally?

Vertical upflow is the standard arrangement for a horizontal separator outlet. Horizontal flow through a vertical vane bank is used in some designs but needs a different drainage arrangement and must be agreed with the manufacturer.

Worked example: sizing a vane pack for horizontal flow

Vane packs are usually sized on the vertical cross-section the gas passes through, using the same capacity-factor form as a mesh pad but with a higher K.

Step Calculation Result
Duty 5,000 m³/h at operating conditions, gas density 1.2 kg/m³, liquid density 1,000 kg/m³ 1.39 m³/s
Density term √((1,000 − 1.2) / 1.2) 28.8
Maximum velocity, K = 0.152 m/s 0.152 × 28.8 4.39 m/s
Design velocity, 70% of maximum 0.70 × 4.39 3.07 m/s
Required cross-section 1.39 / 3.07 0.45 m²
Practical section 0.65 m height × 0.70 m width 0.455 m²

The section is then divided into packs by the drainage requirement, not by convenience. Each pack needs a liquid collection point, and the depth has to be enough for the droplets to reach a surface before the gas turns — a pack that is deep enough but has no drainage path between sections simply carries the separated liquid to the next one.

The check that catches most design errors is at the outlet of the last pack rather than at the inlet: with the calculated section, what is the velocity in the gap between the pack and the vessel wall, and does the liquid draining from that pack fall clear of the gas stream or get picked up again? A vane pack that meets the capacity calculation and fails that check produces a wet outlet at design flow, which is usually attributed to the wrong internal.

Operational troubleshooting

How many turns does a vane pack need?

Enough to make the gas change direction at least twice past the drainage point, so droplets that miss on the first turn have a second chance. Single-turn chevrons are adequate for coarse droplets and low velocity; fine droplets and higher velocity need a multi-pass pack with intermediate drainage, and adding passes beyond that raises pressure drop without capture.

Why does a vane pack need a drainage pocket rather than a plain drain?

Because the separated liquid has to leave against the gas flow. A pocket creates a quiescent zone where liquid can accumulate and drain downwards without being re-entrained. Without it, the film runs along the vane and is stripped off again at the vane edge, which is the classic reason a well-designed pack still carries over.

Leave a Reply